Reliable DC Surge Protection Device (SPD) - Type 2, 40kA Direct Current Surge Protector

Product Description

Product Description

SPD Surge Protective Devices are designed to protect against transient surge conditions. Large single surge events, such as lightning, can reach hundreds of thousands of volts and can cause immediate or intermittent equipment failure. However, lightning and utility power anomalies only account for 20% of transient surges. The remaining 80% of surge activity is produced internally. Although these surges may be smaller in magnitude, they occur more frequently and with continuous exposure can degrade sensitive electronic equipment within the facility.


A power surge is a brief overvoltage event that can damage electrical devices and is a common cause for the failure of electrical equipment. Surges can damage and reduce the lifespan of:

• Heating and Air Conditioning Systems
• Washers and Dryers
• Water Heaters
• Ranges & Refrigerators
• Lighting
• Entertainment Systems

NEW 2020 National Electrical Code Requirements
All new and renovated homes are required to be protected by Listed and Approved Type 1 or Type 2 Surge Protective Devices.

Type 1:
Permanently connected Surge Protective Device.  Protects against external and internal surges. May be installed inside or outside the home.

Type 2:
Permanently connected Surge Protective Device installed in, or next to, breaker box. Protects again internal or external surges.

Type 3:
Extra protection. Point-of-use Surge Protective Device. Must be used in conjunction with Type 1 or Type 2 SPD to meet 2020 code requirements.

Use Type 1, 2, and 3 SPDs for the best level of protection.  
 

Product Parameters

Max Continuous Operating Voltage				Ucpv	500VDC	600VDC		1000VDC		1500VDC
Nominal Discharge Current				In	20kA	20kA		20kA		20kA
Max Discharge Current				lmax	40kA	40 kA		40kA		40kA
Protection level				Up	2.8kV	3.0kV		3.5kV		5.5 kV
Rated shortcircuit current				IscCI	100A
lcpv					0.2 mA
Connection mode					paralle
Response Time				tA	25ns
Back up fuse					LT-SSD40
Remotecommunication					With
Remote communication connection					1411:NO,1112:NC
Remote contact rated current					220V/0.5A
Associated disconnectors
Thermal disconnector					internal
Fuses					Fuses type gG100A
ground fault breaker					None
Mechnical characteristics
Connection					By screw terminals:6-35mm
Terminal Screw Torque					2.5 Nm
RecommendedCable cross Section					≥16mm²
Insertwire length					15mm
Mounting					DIN rail 35mm (EN60715)
Degree of Protection					IP20
Housing					PBT
Flame retardant grade					UL94 V0
Operating temperature					-40ºC~+70ºC
Operatingrelative humidity					5%-95%
Working atmospheric pressure					70kPa~106kPa
Connection					By screw terminals:6-35mm

Installation Instructions

Selection of SPD:
For a power distribution system, the main characteristics used to define the lightning protection system and select a SPD to protect an electrical installation in a building are:

• SPD
  • quantity of SPD
  • type
  • level of exposure to define the SPD's maximum discharge current Imax.
• Short circuit protection device
  • maximum discharge current Imax;
  • short-circuit current Isc at the point of installation.

The other characteristics for selection of a SPD are predefined for an electrical installation.

• number of poles in SPD;
• voltage protection level Up;
• operating voltage Uc.

This sub-section Design of the electrical installation protection system describes in greater detail the criteria for selection of the protection system according to the characteristics of the installation, the equipment to be protected and the environment.

Location and types of SPD:


Connection of SPD:
Connections of a SPD to the loads should be as short as possible in order to reduce the value of the voltage protection level (installed Up) on the terminals of the protected equipment.

The total length of SPD connections to the network and the earth terminal block should not exceed 50 cm.

                                    SPD in plastic enclosure                                                                             SPD in metal enclosure
 

 

RED: Replace
Once the indicator shows RED, the product must be replaced.